Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
extruder-options [2019/12/20 14:09]
wolfmanjm
extruder-options [2021/02/22 17:49] (current)
Line 1: Line 1:
-|| extruder.[[module_name]].enable || true || Whether to activate the extruder module at all. All configuration is ignored if false. Each time an <kbd>extruder.[[module_name]].enable</kbd> line is encountered, an extruder module with the name «[[module_name]]» will be created. ||  +| extruder.[[module_name]].enable | true | Whether to activate the extruder module at all. All configuration is ignored if false. Each time an <kbd>extruder.[[module_name]].enable</kbd> line is encountered, an extruder module with the name «[[module_name]]» will be created. |  
-|| extruder.[[module_name]].steps_per_mm || 140 || Steps/millimetre for the extruder stepper motor. This is the number of steps to move one millimetre of filament. [[http://smoothieware.org/extruder#steps_per_millimeter|Learn more]] ||  +| extruder.[[module_name]].steps_per_mm | 140 | Steps/millimetre for the extruder stepper motor. This is the number of steps to move one millimetre of filament. [[http://smoothieware.org/extruder#steps_per_millimeter|Learn more]] |  
-|| extruder.[[module_name]].filament_diameter || 1.74 || Filament diameter, in millimetres, used for volumetric extrusion control. [[http://smoothieware.org/extruder#filament-diameter|Learn more]] |+| extruder.[[module_name]].filament_diameter | 1.74 | Filament diameter, in millimetres, used for volumetric extrusion control. [[http://smoothieware.org/extruder#filament-diameter|Learn more]] | 
-|| extruder.[[module_name]].default_feed_rate || 600 || Default rate in millimetres/minute for moves where only the extruder moves. This is only used if you have never provided a feedrate via the <kbd>F</kbd> parameter. Once you specify a <kbd>F</kbd> parameter, it will be used as the Extruder feed rate until you reset the board. ||  +| extruder.[[module_name]].default_feed_rate | 600 | Default rate in millimetres/minute for moves where only the extruder moves. This is only used if you have never provided a feedrate via the <kbd>F</kbd> parameter. Once you specify a <kbd>F</kbd> parameter, it will be used as the Extruder feed rate until you reset the board. |  
-|| extruder.[[module_name]].acceleration || 500 || Acceleration for the extruder stepper motor, in millimetres/second/second ||  +| extruder.[[module_name]].acceleration | 500 | Acceleration for the extruder stepper motor, in millimetres/second/second |  
-|| extruder.[[module_name]].max_speed || 50 || Maximum allowable speed for the extruder stepper motor, in millimetres/second ||  +| extruder.[[module_name]].max_speed | 50 | Maximum allowable speed for the extruder stepper motor, in millimetres/second |  
-|| extruder.[[module_name]].step_pin || <kbd>2.3</kbd> || Pin for extruder stepper motor driver's step signal ||  +| extruder.[[module_name]].step_pin | <kbd>2.3</kbd> | Pin for extruder stepper motor driver's step signal |  
-|| extruder.[[module_name]].dir_pin || <kbd>0.22</kbd> || Pin for extruder stepper motor driver's direction signal ||  +| extruder.[[module_name]].dir_pin | <kbd>0.22</kbd> | Pin for extruder stepper motor driver's direction signal |  
-|| extruder.[[module_name]].en_pin || <kbd>0.21</kbd> || Pin for extruder stepper motor driver's enable signal ||  +| extruder.[[module_name]].en_pin | <kbd>0.21</kbd> | Pin for extruder stepper motor driver's enable signal |  
-|| extruder.[[module_name]].x_offset || 0 || Extruder offset from origin in millimetres for the X axis. ONLY used when you have multiple extruders to specify the offset from each extruder to the first one. ||  +| extruder.[[module_name]].x_offset | 0 | Extruder offset from origin in millimetres for the X axis. ONLY used when you have multiple extruders to specify the offset from each extruder to the first one. |  
-|| extruder.[[module_name]].y_offset || 0 ||  Extruder offset from origin in millimetres for the Y axis. ONLY used for multiple extruders ||  +| extruder.[[module_name]].y_offset | 0 |  Extruder offset from origin in millimetres for the Y axis. ONLY used for multiple extruders |  
-|| extruder.[[module_name]].z_offset || 0 ||  Extruder offset from origin in millimetres for the Z axis. ONLY used for multiple extruders ||  +| extruder.[[module_name]].z_offset | 0 |  Extruder offset from origin in millimetres for the Z axis. ONLY used for multiple extruders |  
-|| extruder.[[module_name]].retract_length || 3 || Retract length in millimetres. Retract is a retractation of the filament called using the <kbd>G10</kbd> G-code. It is recovered ( reverted ) using the <kbd>G11</kbd> G-code. [[http://smoothieware.org/extruder#retract|Learn more about retractation]]  ||  +| extruder.[[module_name]].retract_length | 3 | Retract length in millimetres. Retract is a retractation of the filament called using the <kbd>G10</kbd> G-code. It is recovered ( reverted ) using the <kbd>G11</kbd> G-code. [[http://smoothieware.org/extruder#retract|Learn more about retractation]]  |  
-|| extruder.[[module_name]].retract_feedrate || 45 || Retract feed-rate ( filament speed ) in millimetres/second ||  +| extruder.[[module_name]].retract_feedrate | 45 | Retract feed-rate ( filament speed ) in millimetres/second |  
-|| extruder.[[module_name]].retract_recover_length || 0 || Additional length when recovering ( if you retract by 1mm, you will be recovering by 1mm plus this value ) ||  +| extruder.[[module_name]].retract_recover_length | 0 | Additional length when recovering ( if you retract by 1mm, you will be recovering by 1mm plus this value ) |  
-|| extruder.[[module_name]].retract_recover_feedrate || 8 || Recovery feed-rate in millimetres/second (should be less than retract feedrate) ||  +| extruder.[[module_name]].retract_recover_feedrate | 8 | Recovery feed-rate in millimetres/second (should be less than retract feedrate) |  
-|| extruder.[[module_name]].retract_zlift_length || 0 || Z-lift on retract in millimeters, set to <kbd> 0 </kbd> if you want to disable retraction Z-lift. Z-lift is a small increase in the Z axis position when retracting. ||  +| extruder.[[module_name]].retract_zlift_length | 0 | Z-lift on retract in millimeters, set to <kbd> 0 </kbd> if you want to disable retraction Z-lift. Z-lift is a small increase in the Z axis position when retracting. |  
-|| extruder.[[module_name]].retract_zlift_feedrate || 6000 || Z-lift feed-rate in millimetres/minute ( Note : mm/min NOT mm/sec) ||  +| extruder.[[module_name]].retract_zlift_feedrate | 6000 | Z-lift feed-rate in millimetres/minute ( Note : mm/min NOT mm/sec) |  
-|| delta_current || 1.5 || First extruder stepper motor driver ( M4 ) current in Amperes ||  +| delta_current | 1.5 | First extruder stepper motor driver ( M4 ) current in Amperes |  
-|| epsilon_current || 1.5 || Second extruder stepper motor driver ( M5 ) current in Amperes ||+| epsilon_current | 1.5 | Second extruder stepper motor driver ( M5 ) current in Amperes |